RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: mikes68charger
Showing results 1 to 25 of 34
Search took 0.01 seconds.
Forum: RC Jets
04-10-2022, 03:34 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

Without pulling mine back down, thats about all i...

Without pulling mine back down, thats about all i can get also. It must of been enough for my maiden flight. But I would also feel better if someone who Is flying there could commit on elevators...
Forum: RC Jets
04-06-2022, 07:04 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

I worked on mine this week, put the single pipe...

I worked on mine this week, put the single pipe in angled motor 8 deg to outward. K hope it's enough. I did add 7oz of led in wing to balance left and right weight. But had to move batteries out if...
Forum: RC Jets
02-07-2022, 12:27 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg5.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg5.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/403x302/106719270_3275510055804156_5172402643145768449_n_3c2ca24b157792000fad0b0ccb19488b5f5b7574.jpg...
Forum: RC Jets
02-07-2022, 12:08 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

LOL Thanks, now that Im back from my year...

LOL Thanks, now that Im back from my year deployment, Im just waiting for the snow to melt to get this big girl in the air again.
Forum: RC Jets
12-01-2020, 09:25 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

Great work! How many oz do your tanks hold? I...

Great work! How many oz do your tanks hold? I put 2 Dubro 80oz tanks in line as far forward between intakes as possible.

Where you get your pipe? Mine came with a Y pipe but it has 4 small...
Forum: RC Jets
01-23-2020, 01:41 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

Great looking hatch there. I finally got my...

Great looking hatch there.

I finally got my K180G2 running correctly on Diesel last week, and its been sitting in my cold As grauge sinc .

I'm at the fuse bodywork and adding pannels to the...
Forum: RC Jets
12-17-2019, 11:27 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

Well its fiberglass time, I normally use 1/2 oz...

Well its fiberglass time, I normally use 1/2 oz cloth for my wood builds, but I wanted to add more strength in these foam parts, so I used 3/4 oz cloth, (Pluse getting 1/2 oz cloth is getting hard to...
Forum: RC Jets
12-17-2019, 09:24 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg6.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg6.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20191216_130232_58ecaab4577154605f617702404f8c075eb65b46.jpg...
Forum: RC Jets
12-10-2019, 04:03 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

Ya no rotation needed, the jet is never close...

Ya no rotation needed, the jet is never close enough to see them rotate
Forum: RC Jets
12-10-2019, 03:02 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20191210_111058_ce3cecc8b73bd6167c10b195f0fabb3a80086839.jpg...
Forum: RC Jets
12-06-2019, 05:00 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

So used my drill bit to get holes for carbonfiber...

So used my drill bit to get holes for carbonfiber rods nice and straight, then put rod in drill, and drilled it all the way in.

Then cut channels in for carbonfiber flat peaces with groves cut in...
Forum: RC Jets
12-06-2019, 04:58 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg7.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg7.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20191206_195501_1872ad7b585178fe10ee7466cf2ddf6b2793d948.jpg...
Forum: RC Jets
12-04-2019, 11:42 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://www.rcgroups.com/forums/showthread.php?281...

https://www.rcgroups.com/forums/showthread.php?2816053-Attention-Skymaster-F15-owners!-Scale-exhaust-nozzles...
Forum: RC Jets
12-04-2019, 11:30 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

I would move the pipe forward a tad, Make the...

I would move the pipe forward a tad, Make the tail pipe flush or a tiny bit inside the fuse, I don't have a single just that the pip actually sits out like that. Pulse with the huge outlets we have...
Forum: RC Jets
12-03-2019, 07:49 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

Ohh I agree the nose gear was even harder, got...

Ohh I agree the nose gear was even harder, got upset and hit the screw heads with drimel, but the 2 inside the lower part of brackets was almost impossible, I just hammered the whole nose gear wood...
Forum: RC Jets
12-03-2019, 06:39 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

So wireing harnesses and air harnesses are done,...

So wireing harnesses and air harnesses are done, all net, as and covered in sheath to protect wires and hoses

Aluminum heat shield on the only part that will be close to the pipe, and radiates up....
Forum: RC Jets
12-03-2019, 06:32 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg7.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg7.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20191202_212947_1f0e3a919539137e588a5584a0c73291e7b84f6f.jpg...
Forum: RC Jets
12-03-2019, 02:55 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

Yes that's the tape I use, I put a thin bead of...

Yes that's the tape I use, I put a thin bead of 100% silicone throw the center of the strip to help hold on when upside down.

Also in your other project that the pipe is much close to fuse, I...
Forum: RC Jets
12-03-2019, 11:41 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

Thanks, I will do this with a nice peace of 1/4in...

Thanks, I will do this with a nice peace of 1/4in wide x 1.5 carbon fiber, I will cut 2 channels around the tube to put these carbonfiber ribs in, then I will glass it. Glassing will be my last step,...
Forum: RC Jets
12-03-2019, 07:42 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

Your right, If it was up to me, I would of put...

Your right, If it was up to me, I would of put the motor farther forward, but someone else already cut the back hatch and got the pipe, so I worked with what I had.

I will add heat alum tape, with...
Forum: RC Jets
12-02-2019, 04:07 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

Well took 2 days But had to completely change the...

Well took 2 days But had to completely change the top hatch operation. The skin by it self is like paper.

So I needed to add support from the 2 formers, so I used 2 1/4in hard wood to attach both...
Forum: RC Jets
12-02-2019, 04:02 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg5.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg5.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20191202_185714_7efcc45dfe752a77c828a639fff0a4fa00281937.jpg...
Forum: RC Jets
11-28-2019, 09:56 AM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg9.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg9.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20191128_125327_e12a045f1193a665f6199d76f2f8ead35dae867e.jpg
The motor finally started and ran great. It has a issues, after...
Forum: RC Jets
11-27-2019, 09:22 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

So now not my favorite part, thrust tube setting,...

So now not my favorite part, thrust tube setting, most manual says 25-30mm from inside pipe, some manual say line end of bellmouth with end of pipe. I see a lot of pictures like how I have it set up....
Forum: RC Jets
11-27-2019, 09:18 PM
Replies: 258
Views: 48,587
Posted By mikes68charger

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/1500x2000/20191128_001342_231476b1a5074071a0eadc72f9ba9a6844699c53.jpg...
Showing results 1 to 25 of 34
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.