RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: burtona
Showing results 1 to 12 of 12
Search took 0.05 seconds.
Forum: Classic RC Pattern Flying
07-02-2012, 02:17 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

Sounds like you have a Bob Godfrey laser. He sold them mostly in the bones (framed up but not covered I think). Lots of them were used in TOC contest in years after 1978. I think the basis of his...
Forum: Classic RC Pattern Flying
05-07-2011, 11:57 AM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

First two flights this AM. Needed a little right aileron trim, nothing else to fly straight and level. I have some aileron differential issues to work out, need more aileron throw and less elevator,...
Forum: Classic RC Pattern Flying
05-05-2011, 09:48 AM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

It's finally finished. Hope to fly first time in the next couple of days, as soon as the wind lays down here. If it flies OK then I got to get in practice flights of the TOC sequence for the Chicago...
Forum: Classic RC Pattern Flying
04-22-2011, 08:07 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

Hi Mark,
I'm looking foreward to flying with you in Chicago.
I haven't flown my Laser yet but I'm hoping the same setup I use in the Integral will work. I'll try a 21 X 14 APC first and see how...
Forum: Classic RC Pattern Flying
04-22-2011, 03:33 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

I'm getting close on mine too. May have it ready to fly next week. Needs a little more trim applied, locating battery tray, installing wheel pants. It weighs about 13.5 lbs with batteries, AXI 5330...
Forum: Classic RC Pattern Flying
02-11-2011, 05:17 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

It's only tempporary. I'm thinking a can of Foster's would provide much more power than the Czech brand!
Dave
Forum: Classic RC Pattern Flying
02-11-2011, 11:54 AM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

More progress.
Ulrey TOC Laser is near finishing stages (i.e. Lots of time consuming detail stuff left to do). All the major construction is done. Motor and cowl mounted, hatch finished with only...
Forum: Classic RC Pattern Flying
01-29-2011, 03:54 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

Cees,
Thanks for the good words. See detail pictures of the stab/fin arrangement below. I use 4 carbon fiber pins into the fusalage bulkhead and the plywood tail post to hold in position. Two 4-40...
Forum: Classic RC Pattern Flying
01-29-2011, 10:28 AM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

Beginning to look like a Laser.
Forum: Classic RC Pattern Flying
01-23-2011, 10:45 AM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

My TOC Laser is progressing. Wing/Stab alignment done and mounting plates installed.
Forum: Classic RC Pattern Flying
01-10-2011, 07:22 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

My electric Ulrey Laser is underway too. Had the plans for many years, finally started it a month or so ago. I'm using an AXI 5330/FAI and 10S packs for power.
Forum: Classic RC Pattern Flying
04-25-2010, 03:07 PM
Replies: 159
Views: 83,783
Posted By burtona

RE: 1980 TOC Laser 200 by Ulery

OK, I got to build this one. I've had the plans in the attic for years, just ordered the FG parts last week. Will there be a 2 piece wing with tube version? Electric option? When will the "elves"...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.